為了避免一些人員和資金的浪費，我們在操作中走絲技術線切割必須具備下列條件，中走絲線切割加工才能正常運行：

1. 鉬絲與工件的被加工表面之間必須保持一定間隙，間隙的寬度由工作電壓、加工量等加工條件而定。

2. 電火花線切割機床加工時，必須在有一定絕緣性能的液體介質中進行，如煤油、皂化油、去離子水等，要求教高絕緣性是為了利于產生脈沖性的火花放電，液體介質還有排除間隙內電蝕產物和冷卻電極作用。鉬絲和工件被加工表面之間保持一定間隙，如果間隙過大，極間電壓不能擊穿極間介質，則不能產生電火花放電；如果間隙過小，則容易形成短路連接，也不能產生電火花放電。

3. 必須采用脈沖電源，即火花放電必須是脈沖性、間歇性，脈沖寬度、to為脈沖間隔、tp為脈沖周期。在脈沖間隔內，使間隙介質消除電離，使下一個脈沖能在兩極間擊穿放電。

線切割加工是一件講究精度的活。工件的切割質量好不好將會直接影響到整個線切割加工過程。